DMX512 Dim CV LED drivers 150w (IP67)
The 12V 150W dmx driver rgb led supports RDM control & setting. Using hand-held device to set NFC address & adjust output voltage. Smarts DMX 512 drivers covers the wattage from 30w to 300w.
| Model | SMT-12150-XC-A | SMT-24150-XC-A | ||
| X=1 , 2, 3, 4, 5 for DIM (DW); CCT(TW); RGB; RGBW; RGBW+CCT (RGBCW) | ||||
| DC Voltage | 12V | 24V | ||
| Voltage Tolerance | ±0.5V | |||
| Voltage Regulation | ±0.5% | |||
| Rated current | CH1+CH2+CH3+CH4+CH5=12.5A | CH1+CH2+CH3+CH4+CH5=6.25A | ||
| Rated power | 150W | |||
| Load Regulation | ±2% | |||
| Input | Voltage Range | 100-277VAC | ||
| Frequency Range | 47-63Hz | |||
| PowerFactor(Typ.)@ full load | PF≥0.97@230VAC | |||
| THD(Typ.)@ full load | ≤10% | |||
| Efficiency(Typ.)@ full load | 91%@230VAC | 92.5%@230VAC | ||
| AC Current(Max.) | 1.85A | 1.85A | ||
| Inrush Current(Typ.) | 88A (Twidth 120us measured at 50% I peak, COLD START, 230VAC) | |||
| Leakage current | <0.50mA | |||
| Protection | Short Circuit | Hiccup mode ,recovers automatically after fault condition is removed | ||
| Over Loading | ≤120% Hiccup mode ,recovers automatically after fault condition is removed | |||
| Over temperature | 100℃±10℃ shut down o/p voltage, automatically recover after cooling. | |||
| Environment | Working TEMP. | -40~+60℃ (see below derating curve) | ||
| Working Humidity | 20~95%RH, non-condensing | |||
| Storage TEMP. Humidity | -40~+80℃,10~95%RH | |||
| TEMP .coefficient | ±0.03%/℃(0~50℃) | |||
| Vibration | 10~500Hz, 5G 10min./1 cycle,period for 60min. each along X,Y,Z axes | |||
| Safety&EMC | Safety standards | EN61347-1 EN61347-2-13 (EU) & UL8750 UL1310 (US) | ||
| Withstand voltage | I/P-O/P:3.75KVAC I/P-FG:1.88KVAC O/P-FG:0.5KVAC (EU) & I/P-O/P:1.5KVAC(US) | |||
| Isolation resistance | I/P-O/P:100MΩ/500VDC/25℃/70%RH | |||
| EMC EMISSION | EN55015 EN61000-3-2 ,3-3 (EU) & FCC Part 15 B (US) (≥60% loading) | |||
| EMC Immunity | EN61000-4-2,3,4,5,6,11, EN61547 | |||
| Others | Net Weight | 0.75KG | ||
| Dimension | 277x78x25mm (LxWxH) | |||
| packing | 10PCS/CTN | |||
| Notes | 1. All parameters NOT specially mentioned are measured at 230VAC input , rated load and 25℃of ambient temperature. | |||
| 2. Tolerance: includes set up tolerance, line regulation and load regulation . | ||||
| 3. The power supply is considered as a component that will be operated in combination with final Equipment. Since EMC performance will be affected by the complete installation, the final equipment manufactures must be-qualify EMC Directive on the complete installation again. | ||||
※Input Rubber cable 3*1.0mm²(VDE approval), the Y/G cable connect with (FG) , Brown with AC (L), Blue with AC(N) (EU)
Input SJOW Rubber cable 3*18AWG (UL approval), the green cable connect with (FG) ,Black with AC (L), White with AC(N) (US)
※Dimming cable: Purple (D+), Brown (D-) and Gray (GND) connect to DMX dimmer / system.
※Output cable to be connected to LED Light;
DIM (DW) dimming: Rubber cable
Black is output ( V+) Positive, White is output (V-) negative
CCT (TW) dimming: 1015 electronic cable , (V+) 16AWG; (V-) 18AWG
Black is output ( V+) Positive, While (CW-) and Yellow (WW-) are output (V-) negative
RGB dimming: 1015 electronic cable , (V+) 16AWG; (V-) 18AWG
Black is output ( V+) Positive, Red (R-), Green (G-) and Blue (B-) are output (V-) negative
RGBW dimming: 1015 electronic cable , (V+) 16AWG; (V-) 18AWG
Black is output ( V+) Positive, Red (R-), Green (G-) ,Blue (B-) , White (W-) are output (V-) negative
RGB+CCT dimming: 1015 electronic cable , (V+) 16AWG; (V-) 18AWG
Black is output ( V+) Positive, Red (R-), Green (G-) ,Blue (B-) , White (CW-) and Yellow (WW-) are output (V-) negative.;
※Please make sure you connect these correctly ,otherwise your product will not work correctly and could be damaged.
Note: there is external antenna at output side. Don't disassemble!
※The default address for the DMX driver is 001.
※Address settings device:
※Address settings:
① RDM setting address:
Set the address by the RDM device. For detailed operation, please refer to RDM device instruction manual.
② NFC setting address:
The DMX address can be read and written by a mobile with Easy NFC APP or NFC handheld device (NFC read & write device: NFC-RW) by close to the NFC signal area of the DMX512 driver.
■ Adjust output voltage Operation
※Adjust output voltage slightly for DMX512 driver
1) The driver output voltage can be read and written by a mobile with Easy NFC APP or NFC handheld device (NFC read & write device: NFC-RW) by close to the NFC signal area of the DMX512 driver.
2) Voltage range: level 1~10, each level is 0.2V. The default output voltage level is 5. Such as SMT-24030-XC-P, default is level 5 corresponding to 24V. By adjusting output voltage slightly, you could get 23.2v to 25V freely.
■ See figure below
Simple operation about DMX512 address reset and adjusting output voltage slighting by a mobile with Easy NFC APP or NFC handheld device (NFC read & write device: NFC-RW)
